Slap Is Dead
BSynth manual

BSynth manual: every control and the signal flow

What each knob, switch and light does in BSynth, the free bass synth plug-in, from the input to the output.

Signal flow

BSynth listens to your bass, analyses it, builds the voices you choose, passes them through the filter and the drive, and blends the result with your clean bass.

The signal flow of BSynth, a free bass synth plug-in: input, dynamics, tracker and dividers, voices, filter with envelope and LFO, drive, mix and output
The owner's manual page inside the plug-in (click the MANUAL tape on the pedal). Read it from the bottom, the input, to the top, the output.
  1. Input. Your bass, mono. A stereo track is summed to mono.
  2. Analysis. Three things are measured: the dynamics (how hard you play), the dividers (a square wave built from your string's waveform, and its octaves) and the tracker (the pitch of the note).
  3. Voices. BASS (your clean bass), SQUARE (fuzz square following the string), SUB (one or two octaves down) and SYNTH (an oscillator following the note) are mixed together.
  4. Filter. The voices go through the resonant filter, moved by the envelope (your playing) and the LFO.
  5. Drive. A soft saturation stage.
  6. Mix. The result is blended with your untouched clean bass.
  7. Output. The LEVEL control, and the footswitch that turns the whole effect on and off.

Voices

ControlWhat it does
BASSYour clean bass, sent through the filter and the drive with the other voices. At zero you hear a pure synth (plus whatever MIX leaves of the untouched bass).
SQUAREThe fuzz square: a square wave that follows your string at the same pitch, instantly, as in classic divider pedals.
SUBThe octave-down voice, made by dividing the signal: it follows your string with no delay.
SUB OCTChooses the sub: one octave down, two octaves down, or both.
SYNTHThe level of the tracking synth voice: an oscillator that follows the pitch of the note you play. In the first moments after a note starts, an analog-style stand-in keeps the sound instant until the tracker has the pitch.

Synth

ControlWhat it does
WAVEMorphs the oscillator continuously from sine through saw and square to a narrow pulse. The sine end carries a little harmonic content so it stays audible on small speakers.
OCTAVEThe pitch of the synth voice relative to your note: −2, −1, 0 or +1 octaves.
DETUNEAdds a second oscillator slightly out of tune, up to about 40 cents of spread, for thick, wide sounds.
GLIDESmooths the pitch changes between notes, from 0 to 400 ms.

Filter

ControlWhat it does
CUTOFFThe resting frequency of the filter, from 40 Hz to 8 kHz. The envelope and the LFO move the filter from here.
RESOResonance: emphasis around the cutoff. At the top the filter approaches self-oscillation.
MODELOW is a 24 dB/octave low-pass filter. BAND is a band-pass filter: it removes the low body and keeps a moving peak, the classic envelope-filter quack. HIGH is a high-pass filter. In BAND and HIGH, the SUB voice goes around the filter so the low end stays solid.
Filter switch and lightThe small switch on the FILTER frame turns the filter and its envelope on and off. The light shows its state.

Envelope

The envelope measures how hard you play and uses it to move the filter's cutoff. It adapts to your recent playing (about the last three seconds), so it works the same whatever your input level.

ControlWhat it does
ATTACKHow fast the filter opens when you play, from 1 to 500 ms. Short for a sharp quack, long for a slow swell.
SWEEPHow far, and in which direction, the filter moves: from −100% to +100%, up to five octaves. Positive opens the filter as you dig in. Negative closes it. At zero the filter stays at the cutoff.
DECAYHow fast the filter returns to the cutoff after the note, from 20 ms to 1.5 s.

LFO

ControlWhat it does
RATEThe speed of the LFO, from 0.1 to 20 Hz. When SYNC is on, the same knob chooses a tempo division of the host: 1/1, 1/2, 1/4, 1/4T, 1/8, 1/8T, 1/16, 1/16T or 1/32.
SYNC / FREELocks the LFO to the song tempo and position, or lets it run free.
DEPTHHow much the LFO moves the filter, up to three octaves each way.

Output

ControlWhat it does
DRIVEA soft saturation stage after the filter, adding up to 30 dB of gain into the saturation, for warmth and grit.
MIXThe balance between the effect and your untouched clean bass. At 100% you hear only the effect.
LEVELThe output level, from −24 dB to +12 dB.
FootswitchTurns the effect on and off. The light above it shows the state; when off, your bass passes through untouched.

Gate and track light

The small GATE knob, next to the TRACK light, sets how loud a note must be before BSynth tracks it, from −80 to −30 dB. Turn it down if soft notes are missed and up if noise or hum triggers the synth. The TRACK light is lit when the synth voice has locked onto the note. BSynth is monophonic: play one note at a time.

Presets

The tape at the bottom left shows the current preset. Click the arrows to step through the presets, or click the name for the menu: the 28 factory presets in four folders (Basics, Classic, Electronic and Slap Is Dead), your own saved presets, Save preset, Import preset pack and Show presets folder. On macOS the factory presets also appear in Logic Pro's preset menu, and your saved presets too.

Under the lid

Click the MANUAL tape on the pedal, then the second tab, UNDER THE LID, to see the plug-in as a circuit board, with each control under its knob and the audio path drawn as copper traces.

Under the lid: the BSynth circuit board with the knobs, chips and traces of the signal path
The circuit board view inside the plug-in.

New to bass synth? Read the guide to using a bass synth plug-in with your bass. Ready to play? Download BSynth free for macOS and Windows.